Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterTrusted Garage Door Installation for Redmond Homeowners
Garage door installation in Redmond typically costs $700-$2,200 depending on door size, material, and hardware selection, and every job starts with a free in-home measure and a flat written price before any work is scheduled. We’re Servo Garage Doors Redmond, independently owned and operated under The Haven Standard since 2015, and we’ve installed more than 18,000 garage doors with a documented photo record and written scope delivered on every job. If your current door is sagging, rusted through, or you’re finishing a new build in Education Hill or Bear Creek, call us at (425) 305-4847 for a free estimate with real numbers you can compare.
Redmond’s wet winters and the freeze-thaw cycles we get January through March beat hard on garage doors. The moisture works into steel panels at the bottom edge, and the temperature swings stress wood doors in neighborhoods like Grass Lawn and North Redmond where many homes went up between 2015 and 2020. We’ve measured doors in Redmond that were installed without proper header support or with openers mismatched to door weight, problems that show up three to five years later as premature wear. Our technicians are background-checked, uniformed, and carry license documentation on every job, not buried in fine print on a website.
Live phone coverage runs 24 hours a day, including holidays. When you call (425) 305-4847, a real person answers, assigns a named technician, and sends an on-the-way text with a photo and ETA. That’s standard for every call, not an upgrade.
What Our Garage Door Installation Service Includes
New Door Installation
New Door Installation is the complete replacement of an existing garage door, including removal and disposal of the old door, installation of the new door system, and connection or upgrade of the opener hardware. You need this when your current door has structural damage, repeated component failures, or aesthetic mismatch with a renovated home exterior. At Servo Garage Doors Redmond, we measure the rough opening with a laser level, inspect the header and jambs for rot or inadequate support common in Redmond’s older Sammamish Valley builds, and deliver a written scope and flat price before we order anything. The photo record starts at this first visit, so you see what we found before any commitment.
Single Car Door Installation
A Single Car Door typically measures 8 to 9 feet wide by 7 to 8 feet high and requires a properly sized torsion spring system calibrated to the door weight. You need this for a one-car garage, a detached workshop, or an ADU conversion where a full-size door would overwhelm the structure. We stock single-door hardware kits for Clopay and Amarr models and can typically measure, quote, and schedule within one visit to your Redmond property. The Haven Standard Clause 1 applies here: the written price covers the complete installed system, including track, springs, rollers, and weatherstripping, with no add-ons after the fact.
Double Car Door Installation
A double car door spans 16 feet wide by 7 to 8 feet high and demands heavier-duty spring hardware, a more powerful opener, and precise track alignment to prevent binding over time. You need this for a two-car garage or when converting a tandem space in newer Redmond developments like Redmond Ridge or Trilogy. We see more double-door installations in Redmond than single, and we’ve documented a pattern of premature cable wear on doors where the original installer used undersized hardware to cut cost. Our quotes specify the wire diameter of the torsion spring, the horsepower of the opener, and the gauge of the track, so you know what you’re paying for.
Custom Garage Door Installation
Custom garage door installation covers non-standard sizes, specialty materials, or design-matched doors for historic homes, modern architect-designed builds, or HOA-mandated aesthetic requirements. You need this when your opening is an unusual dimension, when you’re matching a specific siding or trim profile, or when the neighborhood covenants in areas like Cleveland Street or the Redmond Town Center corridor require a particular style. We work with Clopay’s Reserve Wood and Amarr’s Classica lines for custom applications, and we bring material samples and finish swatches to the measurement appointment. The written quote includes lead time, which runs 4 to 8 weeks for most custom orders, and we coordinate delivery to minimize your garage downtime.
Steel Door Installation
Steel garage doors are constructed from galvanized steel panels with polyurethane or polystyrene insulation cores, offering durability and thermal performance at a moderate price point. You need this when you want low maintenance, good insulation value for an attached garage, and resistance to the denting that plagues aluminum doors. We install steel doors from 24-gauge to 25-gauge panel thickness, with R-values from 6.3 to 18.4, and we recommend the higher insulation grades for Redmond homes where the garage shares a wall with living space. Our quotes break out the panel gauge, the insulation type, and the hardware package separately, so you can see where the money goes.
Wood Door Installation
Wood garage doors are built from layers of cedar, hemlock, or mahogany with overlay or carriage-house designs that suit traditional and craftsman-style homes. You need this when the architectural character of your Redmond home demands natural material, or when you’re replacing a wood door that has reached the end of its serviceable life after 15 to 20 years of Pacific Northwest exposure. We install wood doors with composite or vinyl backer panels to reduce moisture absorption, and we specify the finish schedule, priming, and recommended re-coating interval in the written scope. The photo record documents the door condition at delivery and the finished installation, creating a baseline for future maintenance decisions.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Garage Door Installation
We install and service all eight major garage door brands, and we stock hardware and accessories for the lines we see most often in Redmond homes. Clopay is the largest residential garage door manufacturer in North America, and we’ve installed hundreds of their Gallery and Canyon Ridge collections in Redmond’s newer subdivisions; we carry their OEM track hardware and extension spring kits on every truck. Amarr doors are common in the Pacific Northwest for their steel-core construction and broad dealer network, and we maintain direct supplier relationships that let us source specialty sizes without the markup of a middleman. Wayne Dalton uses a proprietary TorqueMaster spring system that requires specific tools and training to service safely, and our technicians are equipped for both installation and future maintenance of these units. Craftsman doors, sold primarily through Sears and now available through select dealers, often use rebranded Clopay or Wayne Dalton components, and we can identify the original manufacturer to source correct replacement parts when needed.
Whether you have a Clopay, Amarr, Wayne Dalton, Craftsman, or any other make, we can help. Our measurement process identifies the brand, model, and hardware specifications of your existing door, and we cross-reference that against our inventory and supplier network to quote accurately on the first visit. We do not guess at compatibility or promise parts we cannot source.
Before
AfterSigns You Need Garage Door Installation Right Now
- The door panels are rusted through or delaminating. Surface rust can be sanded and painted, but once steel panels perforate or wood layers separate, the structural integrity is compromised and the door will continue to deteriorate. In Redmond’s climate, we see this most often on doors installed before 2010 with inadequate bottom-seal weatherstripping that allowed standing water to wick upward.
- The door has been hit and the track or frame is bent. A vehicle impact or heavy object strike can distort the vertical track, twist the header, or crack the jamb, and these deformities don’t correct themselves. Operating a door on bent track stresses the opener, the rollers, and the spring system, turning one problem into four.
- You’re finishing a new garage or converting a carport. New construction and significant remodels in Redmond require permits and inspections, and the garage door must meet current energy code and wind-load requirements. We pull the permit as part of our installation service and schedule the inspection to match our completion date.
- The door is mismatched to the opener and components fail repeatedly. A 1/2-horsepower opener straining to lift an insulated 16-foot steel door will burn out its logic board, strip the trolley carriage, and overwork the torsion spring. If you’ve replaced the opener twice in five years, the door is probably the wrong weight class for the hardware.
- Your HOA or architectural review board has issued a compliance notice. Many Redmond neighborhoods, particularly in planned communities like Redmond Ridge and English Hill, enforce design standards that older doors no longer meet. We provide documentation of the proposed door style, color, and hardware finish to support your ARC application before we order.
Our Garage Door Installation Process - Step by Step
- 1
Schedule your free measure. Call (425) 305-4847 or request through our live phone coverage. We confirm your address in Redmond, note any access constraints like a steep driveway or gated community, and assign a technician with a 2-hour arrival window. You’ll receive a text with the technician’s name, photo, and vehicle information before they leave our dispatch point.
- 2
On-site inspection and measurement. The technician arrives with a laser measure, level, and camera. We record the rough opening width and height, the headroom above the opening, the backroom depth inside the garage, and the side-room clearance for track. We inspect the header for adequate support, the jambs for plumb and rot, and the concrete floor for level. In Redmond, we frequently find insufficient headroom in garages built before 1980, which requires a low-headroom track kit or a wall-mounted opener, and we note this in the written scope.
- 3
Written price and scope delivery. Before leaving your property, the technician delivers a flat, written price covering the complete installed system: door, hardware, opener if requested, disposal of the old door, permit if required, and the 365-Day Done Right Promise. Clause 1 of The Haven Standard prohibits any work starting without this document signed by both parties. You receive a copy by email before the technician departs.
- 4
Order, delivery, and installation scheduling. For standard doors, lead time is typically 5 to 10 business days. Custom orders run 4 to 8 weeks. We coordinate delivery to our warehouse, inspect the door for shipping damage before bringing it to your home, and schedule installation for a day that works for you. Installation of a standard single or double door takes 3 to 5 hours; custom or complex jobs may extend to a full day.
- 5
Installation, testing, documentation, and walkthrough. The installation crew removes and disposes of the old door, installs the new door system to manufacturer specification, connects or upgrades the opener, and tests all safety systems including the photo-eye sensors and the auto-reverse function. The technician photographs the completed installation, the safety test results, and the serial number plate for your record. You receive the documented photo record by email, along with the warranty documentation and the maintenance schedule, before the crew leaves.
How Much Does Garage Door Installation Cost in Redmond?
A typical new door installation in Redmond runs $700-$2,200 depending on door size, material, insulation level, and hardware selection; see our Garage Door Installation cost guide for details. Here’s how that breaks down for common scenarios we quote:
- Single car, non-insulated steel door with basic hardware: $700-$1,100
- Single car, insulated steel door with mid-grade opener: $1,100-$1,600
- Double car, insulated steel door with premium opener: $1,400-$2,000
- Double car, wood or custom-finish door with hardware upgrade: $1,800-$2,200
- Custom size or specialty material (full-view glass, carriage house overlay): $2,000+
Several factors move the price within these ranges. Door material is the largest variable: steel costs less than wood, and custom finishes or glass panels add 30 to 50 percent. Insulation level matters for attached garages in Redmond’s climate, where an R-16 or R-18 door reduces heat transfer to living space above or beside the garage. Opener horsepower and drive type, belt versus chain versus wall-mounted, add $150-$400 to the total. Hardware upgrades like heavy-duty rollers, tamper-resistant bottom brackets, or wind-load reinforcement for exposed locations also affect the final number.
To avoid overpaying, get the written scope in detail, not just a bottom-line number. A quote that says “install new door, $1,500” without specifying the panel gauge, spring wire diameter, or opener model leaves room for substitution. Our quotes name the part, the specification, and the price of each line item. The total is the total. No add-ons after signature unless you request a change.
What’s included in our free estimate: the on-site measurement, the inspection of structural conditions, the written price and scope, and the photo record of existing conditions. What’s not included until you approve: permit fees, which vary by jurisdiction, and any structural repair to the header, jambs, or concrete that we discover during measurement. If we find rot or inadequate support, we photograph it, explain it, and quote it separately. You decide before any additional work proceeds.
Garage Door Installation Near Redmond - Our Service Area
We install garage doors throughout Redmond and the surrounding communities, with typical scheduling availability within one week for standard doors in Kirkland, Bellevue, Woodinville, Sammamish, Bothell, Issaquah, Newcastle, Seattle, Shoreline, Lynnwood, and Mill Creek. Drive time from our dispatch point to downtown Redmond is under 20 minutes, and we route technicians by neighborhood to keep appointment windows tight. For custom orders, the measurement and quote happen locally; delivery and installation follow the same geographic coverage. Whether you’re in Education Hill, Bear Creek, Grass Lawn, North Redmond, or a new development near Redmond Ridge, the process, the pricing structure, and The Haven Standard documentation apply identically.
Serving Redmond, WA - Our Local Coverage Area
We’re based in the Redmond area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Garage Door Installation in Redmond
Garage door installation is the complete process of removing an existing door and installing a new door system, including the door panels, track, spring hardware, rollers, weatherstripping, and opener connection. The job requires precise measurement of the rough opening, structural inspection of the header and jambs, and calibration of the spring system to the door weight. At Servo Garage Doors Redmond, every Garage Door Installation in Redmond closes with a documented photo record and a written warranty under the 365-Day Done Right Promise. Call (425) 305-4847 to schedule a free measure and written quote.
A standard single or double car door installation takes 3 to 5 hours from removal of the old door to final testing of the new system. Custom doors, structural repairs, or opener upgrades may extend to a full day. The lead time from quote to installation is typically 5 to 10 business days for standard doors and 4 to 8 weeks for custom orders. We schedule installation only after you’ve approved the written price and scope, per Clause 1 of The Haven Standard.
Garage door installation in Redmond costs $700-$2,200 for most residential applications, with single-car non-insulated steel doors at the lower end and custom wood or glass doors at the upper end. The price depends on door size, material, insulation level, hardware grade, and opener selection. Every quote from Servo Garage Doors Redmond is flat, written, and itemized before any work is scheduled. Call (425) 305-4847 for an exact quote on your specific opening, estimates are free.
Yes, we install and service Clopay, Amarr, Wayne Dalton, Craftsman, and all other major brands. We carry Clopay and Amarr hardware kits on our installation trucks and maintain direct supplier relationships for specialty sizes and custom finishes. Our technicians are trained on each manufacturer’s installation requirements and warranty registration process. Whether your existing door is one of these brands or you’re selecting new, we can source, install, and support it.
Emergency service applies to repairs that restore function or security, not to scheduled installations, which require measurement, ordering, and lead time. If your door is damaged and cannot be secured, we offer emergency board-up and temporary securing as a repair service, with same-day response available by calling (425) 305-4847. The permanent installation follows our standard process with written quote and scheduling. Live phone coverage is available 24/7, including holidays, and emergency calls are answered by a real person, not a recording.
Every installation is backed by our 365-Day Done Right Promise: if anything about the installation is not right, we make it right at no additional cost. Manufacturer warranties vary by brand and component, typically 1 year on hardware and 10 years to lifetime on certain door panels, and we register these on your behalf and include the documentation in your photo record. The Haven Standard terms page governs all promises, not a handshake or verbal assurance. You receive written confirmation of all coverage before the crew leaves.
Clear vehicles, storage, and workbenches from the garage to provide 10 feet of clearance in front of the door opening and access to electrical outlets for our tools. Ensure we can reach you by phone on installation day in case the technician needs clarification on opener placement or keypad location. If your HOA requires architectural review, submit our written scope and product literature with your application, we provide these at no charge. The technician handles permit submission if required for your Redmond address.
Schedule Your Garage Door Installation Service in Redmond Today
Call (425) 305-4847 for a free, no-obligation estimate on garage door installation in Redmond. A real person answers 24 hours a day, including holidays. We’ll assign a named technician, send an on-the-way text with photo and ETA, and deliver a flat written price and scope before any work is scheduled. Every installation carries the 365-Day Done Right Promise, the documented photo record, and the terms of The Haven Standard in writing, not as a promise but as a contract. Marcus Deller and the team at Servo Garage Doors Redmond have operated this way since 2015, and we don’t intend to change.
Written by Marcus Deller, Owner at Servo Garage Doors Redmond, serving Redmond, Kirkland, Bellevue, and surrounding communities since 2015.