Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterGenie Garage Door Installation in Redmond: What to Know First
We provide independent Genie garage door installation in Redmond with a flat, written price delivered before any work starts - typical turnaround for a standard single or double door is one scheduled day after measurement. New door installation in Redmond runs $700-$2,200 depending on size, material, and whether we’re pairing it with a new Genie opener or integrating with an existing drive assembly. This page is for Redmond homeowners who own a Genie product and need a new door installed - whether you’re replacing a failed system, upgrading curb appeal, or matching a new build to a Genie opener you already trust. Call (425) 305-4847 to schedule a free measure and written estimate.
How Genie Products Fail - and How We Fix Them
- Genie ChainLift 1200/ChainLift 1000 - stretched chain and worn sprocket. The 1/2-horsepower AC motor in these budget-friendly openers runs a #41 roller chain that elongates faster in Redmond’s wet winters, especially in homes near Marymoor Park where humidity lingers. We measure chain sag against the manufacturer’s 1/2-inch spec and replace both chain and sprocket as a matched set, because a new chain on a worn sprocket fails again in eight months.
- Genie SilentMax 1200/Connect - trolley carriage cracking. The nylon trolley carriage on these belt-drive units carries the full door weight and develops stress fractures after five to seven years. We stock the 36179R.S carriage assembly and the upgraded steel-reinforced version for heavier doors, and we photograph the crack before quoting replacement - Clause 4 of The Haven Standard.
- Genie Intellicode I/II receiver board failure. Early Intellicode boards in pre-2012 units lose programming memory after power fluctuations, common in Redmond’s eastside grid during wind storms. We test the 37028A.S logic board for voltage regulation and replace with a current-production board that holds memory through outages.
- Genie PowerLift 900/1200 - capacitor swelling in the motor housing. These screw-drive units run hot, and the start capacitor degrades from thermal cycling. We pull the motor assembly, check capacitance with a multimeter, and replace the 18043A.S capacitor if it’s drifted more than 10% from spec - a $120-$320 opener repair that beats a full replacement.
- Genie Aladdin Connect module - Wi-Fi dropout in steel garages. The Aladdin Connect smart module mounts inside the opener housing and struggles to maintain signal through steel doors or in homes with metal siding, which we see frequently in Redmond’s newer construction near Education Hill. We relocate the module to an external antenna position or recommend the Aladdin Connect standalone hub for stable connectivity.
Our Genie Garage Door Installation Process
- 1
Free measure and written scope. We photograph your existing opening, check headroom and sideroom for Genie-specific rail geometry, and deliver a flat price before any work starts - Clause 1 of The Haven Standard.
- 2
Parts selection: OEM Genie or verified aftermarket. For Genie opener integration we prefer OEM rail sections and trolley hardware; for rollers, cables, and weather seal we use quality aftermarket equivalents that meet or exceed Genie spec. We document the choice on your written scope.
- 3
Installation and integration. We hang the door, balance the torsion spring or extension spring set, and integrate the Genie opener - setting force limits, travel limits, and safety reverse on the limit switch and force adjustment dials per Genie’s current manual.
- 4
Full cycle testing. We run the door through twenty complete open-close cycles, testing the photo-eye alignment, the mechanical safety release, and the force-reverse function at multiple points along the rail.
- 5
Documented photo record and warranty. You receive photos of the installed system, the written scope with final price, and the 365-Day Done Right Promise. Name the part, quote the range, then get to work.
Before
AfterWhat Genie Garage Door Installation Costs in Redmond
| Service | Price Range |
|---|---|
| New Door Installation (single car, steel) | $700-$1,400 |
| New Door Installation (double car, insulated steel) | $1,200-$1,900 |
| New Door Installation (custom wood or composite) | $1,600-$2,200 |
| Genie Opener Installation (paired with new door) | $250-$550 |
| Track Realignment (if existing track is reused) | $120-$240 |
What moves the price: door size, insulation R-value, window inserts, hardware upgrade to heavy-duty rollers or a quiet nylon roller set, and whether we’re working with standard 12-inch radius track or the low-headroom track common in Redmond’s older split-level homes near Grass Lawn Park. The price we write is the price you pay - no exceptions. Call (425) 305-4847 for a free measure and written estimate.
Why Redmond Homeowners Call Servo Garage Doors Redmond for Genie Work
We’ve made right over 18,000 garage doors since 2015, every one with a written price before work started and a documented photo record when we left. Marcus Deller and our crew have been working Redmond territory for years, including jobs out near Marymoor Park where corrosion from the seasonal wet gets into hardware faster than most people expect. We carry Genie-specific parts on our trucks - trolley carriages, logic boards, rail sections - and when a Genie system isn’t the right fit, we also service LiftMaster and Chamberlain lines with the same flat-price, photo-documented approach. Calls are answered by a live person 24/7, including holidays, and you’ll get a named technician and an on-the-way text, not a callback window.
FAQs
No. Genie opener warranties cover the motor, drive assembly, and electronics for the stated period regardless of door brand, provided the door is properly balanced and within the opener’s rated lift capacity. We verify door weight and spring balance during installation and document both on your photo record. Call (425) 305-4847 if you want us to check compatibility before you buy.
A standard single or double door with a Genie opener takes four to six hours from arrival to final test, assuming standard headroom and no structural modifications. Custom doors or low-headroom retrofits in older Redmond homes add two to three hours. We schedule the full day and finish early rather than rush the test cycle.
Yes, if the opener is under ten years old, the motor and rail are in spec, and the lift capacity matches the new door weight. We inspect the trolley carriage, chain or belt, and logic board during the free measure and tell you honestly whether reuse makes sense or replacement is the better value. The written scope shows both options with separate prices.
We stock common Genie trolley carriages, logic boards, safety sensors, and rail hardware for the ChainLift, SilentMax, and PowerLift series. Specialized or discontinued parts we order with next-day availability for Redmond. If your installation requires a part we don’t have, we tell you before we start - not after we’ve taken the old door down.
No. The written price we deliver after the free measure is the price you pay. If we find rot in the header, uneven concrete, or other structural issues during the measure, we note them and price them before you approve the job - not as surprise add-ons during installation. That’s Clause 1 of The Haven Standard.
Written by Marcus Deller, Owner, Servo Garage Doors Redmond at Servo Garage Doors Redmond, serving Redmond and nearby areas.